TORRIX / UM-O Standard

TORRIX / UM-O Standard

Continuous level measurement with ATEX fulfilling the requirements of the German Water Resources Act (WHG)

Solution for level and overfill prevention

In combination with the UM-O or UM-EX-O the TORRIX is a registered overfill prevention solution and fulfils the requirements of the German Water Resources Act (WHG).

You save space and money, as you don’t need an
additional overfill prevention device.

FAFNIR Process Technology
FAFNIR Process Technology

HPH Ex d

High Pressure Connection Housing

  • On site display for level indication
  • Corrosion resistant (stainless steel 1.4305)
  • Adjustable display
  • 10 mm LED display
  • Easy to install
  • Intrinsically safe power supply for Ex-Zone 0
  • ATEX and IECEx approval
  • Robust design

    DOWNLOAD  

FAFNIR Process Technology

Ex REPEATER/POWER SUPPLY

PR Electronics PRetrans 5104B

  • Current loop : <28 V, max. 600 Ohm
  • Output : 4 - 20 mA
  • Auxiliary power : 24 - 230 V DC/AC
  • Hilfsenergie : 24 bis 230 V DC/AC
  • Snap-on mounting for DIN-rail

Below are examples of where the TORRIX is being used successfully:

Storage Tanks and Storage Containers

Storage Tanks and Storage Containers

TORRIX is ideally suited for measuring in all non-adhesive liquids and almost all tank geometries. There is no need to adjust the sensor to the liquid or the shape of the tank. Another advantage is that there are no dead zones in the upper and lower areas. The starting point of the measurement is only defined by the size of the float; therefore the entire volume can be measured and used.

Interface layer measurements where emulsions are present

Interface layer measurements where emulsions are present

When used with HART ® protocol, TORRIX can measure both the interface level and the overall level of a tank. Unlike sensors that operate on the guided microwave principle, the interface layer can be easily recognized even when emulsion is present.

Level Measurement Pilot plant and prototype systems

Pilot plant and prototype systems

The TORRIX 6 with his probe diameter of 6 mm and float diameter of 27 mm is ideal for applications in smaller containers. Unlike most sensors, TORRIX measures in the upper and lower region with no dead zone with the threshold point defined only by the float. The TORRIX is ideal in applications where frequent changes of media are needed as it does not require adjustment.

Highly accurate measurement, ideal for dispensing volume

With an accuracy of up to 0.3 mm, TORRIX can be used for precise level measurement allowing leak detection in small storage tanks.

In combination with a metering valve, the liquid level measurement feature can also be used to fill a well-defined volume in a process tank. Depending on the geometry of the tank, the accuracy with a filling volume of 100 ml is as low as 2%.

Such is the accuracy of TORRIX, it can also be used in a calibration rig to check the accuracy of other level sensors.

Download Order code 

Sales Engineer

Kevin Biehl
Phone: +49/40/39 82 07 - 83
Fax: +49/40/390 63 - 39
E-Mail: kevin.biehl@fafnir.de

Customer and Technical Support

Michael Stier
Phone: +49/40/39 82 07 - 14
Fax: +49/40/390 63 - 39
E-Mail: michael.stier@fafnir.de

Specifications:
Equipment Type
Display
Magnetostrictive Level Measurement
Overfill Prevention
Liquid
Acids
Chemicals
Fuel
Cryogenic Liquids
Solvents
Water
Vessel
Laboratory Bottle
Bulk Tank
Bypass
Intermediate Bulk Container (IBC)
Ship
Underground Storage Tank
Waste Container
Measuring range
100.00 mm up to 6 000.00 mm
Stem diameter
12.00
Process Connection
Fitting
Flange
None
Temperature
-65.00 °C up to 450.00 °C
Pressure
-1.00 bar up to 120.00 bar
Certification
ATEX
None
WHG
Signal output
Relay
Power Supply
115 VAC
230 VAC
24 VAC
24 VDC
Addtitional criteria
Dry run protection
Electropolished

Ordering information